Fibreglass Sectional Overhead Garage Door

2 x Single white cardinal block fibreglass sectional doors
2 x Single white cardinal block fibreglass sectional doors
2 x Single white cardinal block fibreglass sectional doors
Single white horizontal slatted fibreglass sectional door
Single white horizontal slatted fibreglass sectional door
Single white horizontal slatted fibreglass sectional door

Fibreglass doors are fabricated using moulded fibreglass to create the garage door panels.

Fibreglass doors can be used in areas close to the sea, as the fibreglass will not be weathered by the salty sea air, the sun however can fade fibreglass after many years and it is important to remember that fibreglass doors have a galvanised steel frame riveted around the door.

Sectional overhead garage doors, however, do need to have the tracks, hardware, cables and springs regularly sprayed with silicone spray or Q20. Greasing the doors’ hardware is not recommended as the grease forms a grinding paste with dust and sand particles, which encourages rust and decay.

These doors are very light-weight that will help prolong the life of the doors hardware and the fibre panels require no maintenance.

Fibreglass Sectional Overhead Garage Door Sizes

Standard sizes of garage door openings for fibreglass sectional overhead doors:

Door TypeMeasurements
Single fibreglass sectional door2400mm (w) x 2180mm (h)
Double fibreglass sectional door4800mm (w) x 2180mm (h)

It is important to note that these are the standard opening sizes for your garage door opening, as a maximum of 100mm still will be added to these sizes to get the standard panel size of the garage door itself. All sectional overhead doors need to overlap with a minimum of 30mm to a maximum of 100mm, on the inside side walls of the garage. The door should also overlap with 30mm at the top of the garage.

Colour Options

Fibreglass doors can have a wood grain or smooth finish and come in 1 standard colour;

  • White

Other colours are available at an extra charge.


Contact us for a free quote - 072 843 3116

Design Options

The fibreglass sectional overhead doors are available in either a horizontal slatted or cardinal (block) panels. It is however, important to note that if you opt for the blocks and your door is not a standard size, you should consult your installer as to whether the blocks will be cut off, either on the sides or at the top of door, in which case, you should probably have a horizontal slatted door installed.

Requirements / Specifications

Sectional overhead doors should be installed if your garage is on the boundary or if there is limited space in your driveway in front of the garage, this is because sectional overhead doors slide directly up and over into the ceiling of the garage, in five sections, leaving the full opening of the garage available, as opposed to tipping up and out of your garage, as in the case of a tip up door.

Sectional overhead garage doors require 450mm head room, from the bottom of the lintel to the bottom of the ceiling or rafters, for installation.
This amount of head room must follow through 3m back into the garage. It is possible to install a sectional door with a minimum of 250mm head room, however this will require a flip over panel to be installed.
Flip over panel simply means, that when the door is in the closed position, the top panel will still be in a slanted open position, which the motor will then push closed onto the lintel. Therefore, if a flip over panel is installed, a motor is essential to the door closing fully.

For a sectional overhead door to be installed properly the garage needs to have a minimum of 100mm wall nip space on either side of the garage, ideally 150mm nip space is needed.

Single sectional overhead garage doors either get installed with tension or torsion spring mechanisms, but more often than not, single sectionals are installed with tension springs. Double sectional doors should always use a torsion spring mechanism.

  • Tension spring mechanisms have a spring on either side of each track.
  • Torsion spring mechanisms have either one or two springs, depending on the weight of the garage door, mounted onto a torsion pole above the door.

Both these mechanisms neutralise the weight of the garage door, making it easy to manually move the door up and down.

Fibreglass sectional overhead garage doors have a rubber seal inserted onto the bottom of the garage doors which the door to get a complete seal on the bottom floor, preventing far more dust etc, from entering the garage.

Side seals are also available to be installed on the outside of your garage door, on either side. These are used to completely seal the door from the outside elements, as the rubber seals are placed up right up against the door. A sectional garage door should sit 10mm away from the garage walls, in order to prevent the door scratching on the walls or getting caught on the wall, preventing the door from sliding smoothing up and down.

Contact Us